Manual.ly Logo

Benning MM 6-2 Manual

5,0 · 1 Valoraciones

Manual en PDF · 144 Páginas

Español

M: QW-35-FL
página

/ 144

Loading...
1073337a83fe56817a21cbe9219ad899d4d3 page 1d
02/ 2020
BENNING MM 6-1/ 6-2
29
tivity).
- Connect the red safety measuring lead to the jack
J
for V of the
BENNING MM 6-1/ MM 6-2.
- Bring the safety measuring lead into contact with the measuring point of the
system part.
- If an acoustic signal is emitted and the red LED
N
lights, the phase of an
earthed alternating voltage is applied to this measuring point (system part).
9. Maintenance
Before opening the BENNING MM 6-1/ MM 6-2, ensure that it is
not connected to a source of voltage! Electrical hazard!
Any work required on the BENNING MM 6-1/ MM 6-2 when it is under voltage must
be done only by a qualified electrician. Special steps must be taken to prevent
accidents. Before opening the BENNING MM 6-1/ MM 6-2, remove it from all sources
of voltage as follows:
- First remove both safety measuring leads from the measurement points.
- Remove both safety measuring leads from the BENNING MM 6-1/ MM 6-2
- Turn the rotating switch
to “OFF”.
9.1 Securing the unit
Under certain circumstances, the safety of the BENNING MM 6-1/ MM 6-2 can
no longer be guaranteed. This may be the case if:
- there are visible signs of damage on the unit,
- errors occur in measurements,
-
the unit has been stored for a long period of time under the wrong conditions, and
- if the unit has been subjected to rough handling during transport.
In these cases, the BENNING MM 6-1/ MM 6-2 must be switched off immediately,
removed from the measuring points and secured to prevent it from being used again.
9.2 Cleaning
Clean the outside of the unit with a clean dry cloth. (Exception: any type of
special cleaning cloth). Never use solvents or abrasives to clean the testing unit.
Ensure that the battery compartment and the battery contacts have not been
contaminated by electrolyte leakage.
If any electrolyte or white deposits are seen near to the battery or in the battery
compartment, remove them with a dry cloth, too.
9.3 Battery replacement
Before opening the BENNING MM 6-1/ MM 6-2, ensure that it is
not connected to a source of voltage! Electrical hazard!
The BENNING MM 6-1/ MM 6-2 is supplied by means of one 9 V block battery.
Battery replacement (see figure 13) is required as soon as all segments of the
battery symbol
3
have disappeared and the battery symbol is flashing.
To replace the battery, proceed as follows:
- First remove the safety measuring leads from the measurement circuit.
- Remove the safety measuring leads from the BENNING MM 6-1/ MM 6-2.
- Turn the rotating switch
to “OFF”.
- Remove the protective rubber holster
M
from the BENNING MM 6-1/ MM 6-2.
- Lay the BENNING MM 6-1/ MM 6-2 on its front and loosen the screw from
the cover of the battery compartment.
- Lift off the battery compartment cover from the bottom part of the battery
compartment.
- Lift the discharged battery out of the battery compartment and remove the
battery leads carefully from the battery.
- Connect the new battery with the battery leads and arrange them in such a
way that they are not crushed between the two halves of the housing. Then
place the battery in the correct position in the battery compartment.
- Clip the battery cover onto the bottom part and tighten the screws.
- Replace the BENNING MM 6-1/ MM 6-2 in its protective rubber holster
M
.
See fig. 13: Battery replacement
Remember the environment! Do not dispose of used batteries
with domestic waste. Dispose of them at a battery-collection
point or as toxic waste. Your local authority will give you the
information you need.

Chatee con su manual de Benning MM 6-2 usando IA

Obtenga respuestas instantáneas de IA de su manual de Benning MM 6-2

Pregunte lo que quiera sobre Benning MM 6-2. Las respuestas provienen de este manual, con las páginas en las que se basan.

MM 6-2 Programa de mantenimiento

Recuérdame cuándo corresponde realizar el mantenimiento
Anual
Calibrar el multímetro

Envíe el dispositivo al Centro de Servicio Benning para su recalibración y mantener la precisión especificada. El intervalo recomendado es de un año.

Mostrar en el manual (página 30)
Regularmente
Limpiar la carcasa

Limpie el exterior de la unidad con un paño limpio y seco o un paño de limpieza especial. No utilice disolventes ni abrasivos.

Mostrar en el manual (página 29)
Según sea necesario
Sustituir la batería de 9V

Sustituya la batería cuando desaparezcan todos los segmentos del símbolo de batería y este parpadee.

Mostrar en el manual (página 29)
Antes de cada uso
Inspeccionar el dispositivo y las sondas

Compruebe el instrumento y las puntas de medición en busca de señales de daño antes de iniciar la operación. Asegúrese contra el uso accidental si está dañado.

Mostrar en el manual (página 21)

Recordatorios de mantenimiento gratuitos

Según la fecha de compra. Siempre gratis, cancela la suscripción cuando quieras.

Al enviar, aceptas la política de privacidad. Cancela la suscripción con un clic en cualquier correo electrónico.
M: qwen/qwen3.8-flash

Haz una Pregunta

0/1000

¿Recomiendas MM 6-2?

Sí No
0
User Pic

Margarita Simonis

hace 4 meses

¿Este multímetro detecta automáticamente si estoy midiendo voltaje de CA o CC?

0
User Pic

Manual.ly

hace 4 meses

Sí, el Benning MM 6-2 cuenta con una función AutoV que identifica automáticamente si el valor medido es corriente continua (CC) o alterna (CA). Esto garantiza lecturas precisas sin necesidad de cambiar manualmente. El dispositivo también incluye una función de apagado automático de 20 minutos para preservar la vida útil de la batería y viene con una funda protectora que contiene un imán para operar con las manos libres.

M: QW-35-FL
M: QW-35-FL
0
User Pic

Jace Lowe

hace 6 meses

¿La batería viene incluida en la caja o necesito comprarla por separado?

M: QW-35-FL

Preguntas frecuentes

A

El dispositivo está clasificado para CAT IV 600 V entre conductor y tierra, y CAT III 1000 V para mediciones de línea a línea. No debe usarse en circuitos que excedan estos límites.

¿Esta respuesta fue útil?

A

Sí, pero solo si está equipado con el sensor de temperatura de cable tipo K opcional. La unidad estándar mide voltaje, corriente, resistencia, frecuencia y capacitancia directamente.

¿Esta respuesta fue útil?

A

Aparece un símbolo de batería en la pantalla. Cuando todos los segmentos desaparecen y el símbolo comienza a parpadear, la batería debe reemplazarse inmediatamente para evitar errores de medición.

¿Esta respuesta fue útil?

A

No, el dispositivo está diseñado exclusivamente para entornos secos. Tiene una clasificación IP30, que no ofrece protección contra la entrada de agua.

¿Esta respuesta fue útil?

A

La tecla de función azul selecciona funciones secundarias para las posiciones del interruptor giratorio, como cambiar entre tipos de corriente CA/CC o habilitar modos de medición de frecuencia.

¿Esta respuesta fue útil?

A

Benning recomienda calibrar el dispositivo anualmente enviándolo a su centro de servicio para mantener las especificaciones de precisión especificadas garantizadas para el primer año.

¿Esta respuesta fue útil?

M: QW-35-FL

Ventajas y Desventajas

Ventajas

  • Medición True RMS para lecturas precisas en señales no sinusoidales
  • Clasificación de seguridad CAT IV 600V y CAT III 1000V para entornos de alto riesgo
  • Detección de voltaje sin contacto VoltSense con alertas auditivas y visuales
  • La selección de rango automático simplifica la operación para diagnósticos rápidos
  • Fundición de goma duradera con imán integrado para uso manos libres
VS

Desventajas

  • La medición de temperatura requiere un accesorio sensor tipo K separado
  • Sin iluminación de retroiluminación para condiciones de poca luz
  • El reemplazo de la batería requiere retirar la funda de goma protectora
  • El cambio manual de rangos puede ser menos intuitivo que los modelos totalmente automáticos
  • El voltaje máximo contra tierra está limitado a 600V en configuraciones CAT IV
M: QW-35-FL

Producto Especificación

Rango de medición

máx. 10 A, máx. 1000 V, máx. 40 MΩ

Contenido del paquete

Bolsa

M: QW-35-FL

Producto Descripción

Multímetro Benning MM 6-2: Precisión y Seguridad para Profesionales

El multímetro Benning MM 6-2 se erige como una herramienta robusta diseñada para electricistas e individuos técnicamente capacitados que exigen alta precisión en sus mediciones. Este dispositivo digital sobresale en entornos secos, ofreciendo un conjunto completo de funciones incluyendo voltaje de corriente continua, voltaje de corriente alterna, resistencia, prueba de diodos, comprobaciones de continuidad, medición de capacitancia, análisis de frecuencia y monitoreo de temperatura mediante el sensor opcional tipo K. Su capacidad True RMS asegura lecturas confiables incluso con formas de onda no sinusoidales, lo que lo hace indispensable para diagnósticos eléctricos complejos.

La seguridad es primordial en el diseño del Benning MM 6-2. Clasificado para CAT IV 600 V y CAT III 1000 V, proporciona un entorno seguro para trabajar en circuitos de alta energía cuando se usa con cables de seguridad adecuados y tapas protectoras. La unidad cuenta con tecnología VoltSense para detección de voltaje sin contacto, alertando a los usuarios sobre fases activas mediante un zumbador audible e indicador LED rojo sin necesidad de contacto físico. La pantalla inteligente incluye una barra gráfica para visualizar tendencias y función de apagado automático para conservar la vida útil de la batería de 9 voltios, que puede alcanzar hasta 200 horas con energía alcalina.

La ergonomía también está considerada, con un marco protector de goma duradero que protege el dispositivo de daños mecánicos. Este marco sirve también como soporte para una lectura más fácil e incluye un imán para operación manos libres. El estuche de transporte compacto incluido y los cables de seguridad aseguran que el multímetro esté siempre listo para su despliegue inmediato en cualquier sitio de trabajo. Ya sea verificando continuidad con un zumbador o midiendo microamperios, el Benning MM 6-2 ofrece la precisión requerida para trabajos eléctricos de grado profesional.

M: QW-35-FL

© Copyright 2026 Manual.ly